USFloors® Cork Underlayment Adhesive | 04Y25
This product is relabeled as Shaw Multipurpose 1500 Adhesive; click to visit.
USFloors Cork Underlayment Multipurpose Adhesive 4-Gallon Size. 4 gal covers apx. 800 square feet. US Floors® Cork Underlayment Multipurpose Adhesive is a solvent free, nonflammable, latex based adhesive used for the interior installation of a wide variety of flooring materials. 2085 provides a strong bond, has excellent open time, wet tack and high ultimate strength. Do not use outdoors. USE TO INSTALL: Carpet: jute, latex unitary, polypropylene (actionbac®), needle punched, polyurethane laminate, attached polyurethane cushion, woven carpet, rubber foam back, all backings designed for the installation of direct glue down carpet, and manufacturer approved double-stick installations. For more information on approved double-stick carpet pad and double-stick installations, contact USFloors Technical Services at 800-404- 2675. Sheet goods: commercial, felt-back and inlaid sheet vinyl. NOT recommended for vinyl back flooring of any kind. USE OVER: Concrete: above, on or below grade in the absence of excessive moisture and alkali. APA registered plywood underlayment, hardboard, association grade particleboard. NOT recommended over existing vinyl flooring.
FLOOR PREPARATION: Floor must be clean, level and dry. Remove all foreign substances such as wax, grease, dirt and any substance or chemical that would interfere with a good bond. Test concrete subfloor for alkalinity (pH of floor should be between 5 and 9). Take corrective measures if concrete surface pH is outside these limits. Moisture tests should be performed using an anhydrous calcium chloride test according to ASTM F-1869 test method. Moisture emissions should not exceed 5.0 lbs. per 1000 square feet per 24 hours (2.27 kg/92.9m2/24 hours). Relative Humidity readings according to ASTM F-2170 should not exceed (RH) 85%. If both tests are performed the RH test is the qualifying standard. Fill all holes and cracks with a Portland cement based patching compound. Sand high spots, install underlayment grade plywood or particleboard underlayment over tongue and groove flooring to eliminate the possibility of telegraphing. For best results, the room, floor covering and adhesive should be between 65°F (18°C) and 95o F (35o C) and at a relative humidity between 30% and 60% for 24 hours before, during and after the installation.
USFloors Cork Underlayment Multipurpose Adhesive: USFloors Cork Underlayment Multipurpose Adhesive is a solvent free, nonflammable, latex based adhesive used for the interior installation of a wide variety of flooring materials. 2085 provides a strong bond, has excellent open time, wet tack and high ultimate strength. Do not use outdoors.
USE TO INSTALL: Carpet: jute, latex unitary, polypropylene (actionbac®), needle punched, polyurethane laminate, attached polyurethane cushion, woven carpet, rubber foam back, all backings designed for the installation of direct glue down carpet, and manufacturer approved double-stick installations. For more information on approved double-stick carpet pad and double-stick installations, contact USFloors Technical Services at 800-404-2675. Sheet goods: commercial, felt-back and inlaid sheet vinyl. NOT recommended for vinyl back flooring of any kind.
USE OVER: Concrete: above, on or below grade in the absence of excessive moisture and alkali. APA registered plywood underlayment, hardboard, association grade particleboard. NOT recommended over existing vinyl flooring.
FLOOR PREPARATION: Floor must be clean, level and dry. Remove all foreign substances such as wax, grease, dirt and any substance or chemical that would interfere with a good bond. Test concrete subfloor for alkalinity (pH of floor should be between 5 and 9). Take corrective measures if concrete surface pH is outside these limits. Moisture tests should be performed using an anhydrous calcium chloride test according to ASTM F-1869 test method. Moisture emissions should not exceed 5.0 lbs. per 1000 square feet per 24 hours (2.27 kg/92.9m2/24 hours). Relative Humidity readings according to ASTM F-2170 should not exceed (RH) 85%. If both tests are performed the RH test is the qualifying standard. Fill all holes and cracks with a Portland cement based patching compound. Sand high spots, install underlayment grade plywood or particleboard underlayment over tongue and groove flooring to eliminate the possibility of telegraphing. For best results, the room, floor covering and adhesive should be between 65°F (18°C) and 95o F (35o C) and at a relative humidity between 30% and 60% for 24 hours before, during and after the installation.
Cork Underlayment Multipurpose Adhesive Technical Specifications
UPC | n/a |
---|---|
Weight | 1.0000 |
Country of Manufacture | |
Manufacturer | USFloors® |
Brand Name | USFloors |
Warranty | Not available |
Square ft/bx | 550.0000 |
Unit of Measure | Sq Ft. |